【商品說明】
賀！！本公司為原廠GT-521F32指定之台灣代理商 {原裝正式進口}
- 美國 SparkFun 高精度指紋模組 (GT-521F32)(GTM-5210F32)
- 採用 5V TTL UART 串列通訊
- 可儲存200組指紋樣本、360°辨別
- 另有進階版本 (GT-521F52) 功能完全一樣, 但可儲存3000組指紋樣本 1700元
- 建議可搭配FTDI FT232RL USB UART 模組，讓您更加簡單的操控指紋模組
___________________________________________________________
Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Unfortunately, they’re often unreliable or difficult to implement. Well not anymore! This great GT-521F32 fingerprint module from ADH-Tech communicates over TTL Serial so you can easily embed it into your next project. The module itself does all of the heavy lifting behind reading and identifying the fingerprints with an onboard optical sensor and 32-bit ARM Cortex M3 processor.
To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints, and the database of prints can even be downloaded from the unit and distributed to other modules. In addition to the fingerprint “template,” the analyzed version of the print, you can retrieve the image of a fingerprint and even pull raw images from the optical sensor!
This module is the economical version of the GT-521F52 and can store up to 200 different fingerprints. It is capable of 360° fingerprint recognition and download/upload templates using serial interface. Additionally, the GT-521Fxx series features a resolution of 450dpi, with a false acceptance rate of <0.001% and a false rejection rate of <0.1% while only needing <1.5 seconds to identify a unique fingerprint!
The module is small and easy to mount using four mounting holes surrounding the sensor. The onboard JST-SH connector has four signals: Vcc, GND, Tx and Rx. A compatible JST-SH pigtail can be found in the Hookup Accessories section below.
Note: Please be aware that even though this fingerprint scanner is equipped with the same connector we use on all of our Qwiic boards, it is NOT Qwiic or I2C compatible. That being said, all of our Qwiic cables, like our 100mm version, will work for this board.
【產品規格】
- 工作電壓: 指紋辨識模組 3.3V – 6V, 觸控IC 3.3V
- 工作電流: < 130mA
- MCU: HT32F22366, 32-bit ARM® Cortex®-M3核心.
- 指紋儲存數: 200個(ID為0 – 199)
- 通訊介面: UART (TTL準位, 3.3V)
- 速率(Baud rate): 9600, 19200, 38400, 57600, 115200 (預設值為9600)
- 感測器有效面積: 14mm x 12.5mm
- 指紋影像大小: 258 x 202 像素
- 解析度: 450 dpi
- 指紋模板(template): 498 bytes
- 指紋驗證時間 < 1.0秒 (200個指紋)
- 支持360°辨識, 手指可以從任意方向按壓指紋模組
- 1:1 驗證模式 (驗證按壓的指紋是否與指定的ID為同一個指紋)
- 1:N 識別模式 (識別按壓的指紋是已登錄在指紋模組裡的哪一個ID)
- 安全等級: 1-5,預設等級為3. 數值越高代表安全等級越高, 模組在辨識指紋時採取比較嚴格的條件
- 錯誤接受率(FAR): < 0.001% (安全等級3)
- 錯誤拒絕率(FRR): < 0.1% (安全等級3)
- 尺寸 : 36 x 21 x 10 mm
- 重量: 4.7 公克
【發貨清單】
- 指紋辨識模組GTM-5210F32 x 1
- 連接線(長度 10cm) x 1