Note: Arduino ide軟體支援可使用!
【商品說明】
Raspberry Pi Pico 是基於 Raspberry Pi RP2040 微控制器晶片的微控制器板。它被設計為具有靈活數字接口的低成本、高性能微控制器板。 Raspberry Pi Pico 有兩個 ARM Cortex-M0 + 內核，工作頻率高達 133MHz； 256KB 內存； 30 個 GPIO 引腳，內建溫度感測器和實時時鐘(RTC Clock)；以及廣泛的界面選項。這與用於代碼和數據存儲的 2MB 板載 QSPI 閃存相結合。
除了強大的硬件資源外，Pico還有全面完善的軟件支持和社區資源。 它帶有完整的官方 Rasberry Pi C/C++ SDK，Micropython SDK。
可透過Micro usb 傳輸線，輕鬆連結Raspberry Pi Pico的USB接口提供供電及燒錄程式，並支援Arduino ide燒錄及編輯程式!
【產品規格】
- 21 mm × 51 mm form factor
- RP2040 microcontroller chip designed by Raspberry Pi in the UK
- Dual-core Arm Cortex-M0+ processor, flexible clock running up to 133 MHz
- 264KB on-chip SRAM
- 2MB on-board QSPI Flash
- 26 multifunction GPIO pins, including 3 analogue inputs
- 2 × UART, 2 × SPI controllers, 2 × I2C controllers, 16 × PWM channels
- 1 × USB 1.1 controller and PHY, with host and device support
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
- Supported input power 1.8–5.5V DC
- Operating temperature -20°C to +85°C
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Temperature sensor
- Accelerated integer and floating-point libraries on-chip
【發貨清單】
單主板:
- Raspberry PI PICO *1 PCS (無排針)
A套餐:
- Raspberry PI PICO *1 PCS
- 20 PIN 排針 *2
- 3 PIN 排針 *1
- Micro usb 傳輸線 100公分 * 1條
Getting started with C/C++
Blink an LED
The first program anyone writes when using a new microcontroller is to blink an LED on and off. The Raspberry Pi Pico comes with a single LED on-board (connected to GPIO pin 25). You can blink this on and off by,
- Download the Blink UF2
- Push and hold the BOOTSEL button and plug your Pico into the USB port of your Raspberry Pi or other computer.
- It will mount as a Mass Storage Device called RPI-RP2.
- Drag and drop the Blink UF2 binary onto the RPI-RP2 volume.
- Pico will reboot, and the on-board LED should start blinking.
The next program anyone writes is to say 'Hello World' over a USB serial connection.
- Download the 'Hello World' UF2.
- Push and hold the BOOTSEL button and plug your Pico into the USB port of your Raspberry Pi or other computer.
- It will mount as a Mass Storage Device called RPI-RP2.
- Drag and drop the 'Hello World' UF2 binary onto the RPI-RP2 volume. Pico will reboot
- Open a Terminal window and type:
指令>>> sudo apt install minicom
指令>>> minicom -b 115200 -o -D /dev/ttyACM0
You should see 'Hello, world!' printed to the Terminal